Siemens SICAM Q80 Скачать руководство пользователя страница 108

Страница: 108 / 240

108

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

If the extra information could not be found, this is indicated by asterisks around the measurement task
name:

*not SICAM Q80 7KG8080*

data don't come from

SICAM Q80 7KG8080

*auto*

data which were automatically recorded when the device was
started, but don't belong to any measurement task

*not ready*

measurement not finished yet -> data transfer not possible

*unkown_place*

couldn't find info about measurement start

*unkown_Exp*

measurement task info not present

5.1.4.1

Varieties of data import

Automatic data import:

Preferred variety, stationary operation with fixed settings; the easiest option for multiple

devices.

Manual import of measurement device

: Targeted retrieval of specific measured values; device not always

accessible.

Import of data retrieved from the device CF-Card:

E.g. manual retrieval of on-site data after temporary

deployment at various measurement locations.

Data import from a different SICAM Q80 Manager:

By importing the data from the PC's data storage folder

Adoption of measured data originating from an outside SICAM Q80, data transfer for evaluation or Support

This is the variety recommended for transferring the device definitions file.

Содержание SICAM Q80

















































































































































































































































Результаты поиска

Содержание SICAM Q80

Отзывы:

Siemens SICAM Q80, Системное руководство, Страница: 108 / 240

Результаты поиска

Содержание SICAM Q80

Отзывы: