Siemens SICAM Q80 Скачать руководство пользователя страница 176 | Manualshive

Страница: 176 / 240

Siemens SICAM Q80 Скачать руководство пользователя страница 176

176

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

Other commands:

Set defaults:

Sets the default paths.

Set example data:

Sets the default paths for installation of the sample data.

Note

The path for measured data can be changed independently of the database folder.

Comparisons of measured data saved in different databases are not possible.Start: Global
option upon starting the program.

The paths for the data and database must be enabled (reading- + writing rights)

6.3.4.1.2 Options - Setup

Options - Setup

If the option

Use normtest settings

is active, the measurement is only used in compliance with the standard IEC

61000-4-30. Other measurement quantities are not investigated.

For instance, in this case, no current measurement is performed. The aggregation interval is set permanently to 10
min. Additionally, the aggregation over 3s, 10min and 2h are displayed.

Note

If this option was selected during installation of the software, additional

online displays

are

available.

6.3.4.1.3 Options - Start

Global option upon starting the program.

Program start settings

Upon starting

SICAM Q80 Manager

, the configuration last used is loaded automatically.

Class A measurement device as per the standard 61000-4-30 (Among other things: measurement start only
at multiples of 10 minutes. If a radio clock is used, data originating from different measurement devices can
be compared sample-by sample.)

73

«
...
174
175
176
177
178
...
»

Содержание SICAM Q80

















































































































































































































































Отзывы:

Нет отзывов