Siemens Servo i Скачать руководство пользователя страница 57

Страница: 57 / 70

E382 E407E 061 01 01 02

Siemens-Elema AB

Servo

…

Preventive maintenance

7 - 3

Preventive maintenance

Preventive maintenance-kit

Only original parts from Siemens must be used in the

Servo

…

System. Spare parts and maintenance kits can

be ordered from your local Siemens representative.
When performing this maintenance, a ”Preventive

maintenance-kit for Servo

…

” should be used.

The following parts shall be replaced and they are in-

cluded in the ”Preventive maintenance-kit for Servo

…

”:

A. Filters for the gas modules
B. Bacteria filter for the inspiratory pressure

transducer

C. Bacteria filter for the O

cell

D. Nozzle units for the gas modules

SVX9004X

Performing the Preventive maintenance

• Prepare the unit as described in section

”Preparations” in this chapter.

Inspiratory section

• Loosen the screw (1) and lift off the inspiratory

section cover (2).

SVX9111X

Содержание Servo i







































































Результаты поиска

Содержание Servo i

Отзывы:

Siemens Servo i, Руководство по обслуживанию, Страница: 57 / 70

Результаты поиска

Содержание Servo i

Отзывы: