manualshive.com logo in svg

Siemens Servo i, Руководство по обслуживанию, Страница: 14 / 70

Поделиться
Скачать
Siemens Servo i Скачать руководство пользователя страница 14

Siemens-Elema AB

Introduction

Servo

…

E382 E407E 061 01 01 02

2 - 6

2

The upper part of the Patient Unit contains the

inspiratory section and the expiratory section.
The main parts of the inspiratory section are the:
• Two gas modules, Air and O

2

, for regulation of the

inspiratory gas.

• Connector muff.
• Inspiratory pipe with housings for the O

2

 cell and for

the safety valve.

• O

2

 cell incl. bacteria filter.

• Temperature sensor.
• Inspiratory pressure transducer tube incl. bacteria

filter, to connect the inspiratory pressure

transducer.

The main parts of the expiratory section are the:
• Expiratory cassette.
• Expiratory valve coil.
The expiratory cassette is a complete unit and must

not be disassebled. It contains the following parts:
• Expiratory inlet with moisture trap.
• Ultrasonic flowmeter.
• Heating foil to keep a stable temperature in the

expiratory gas.

• Pressure transducer connection, incl. bacteria filter,

to connect the expiratory pressure transducer.

• Expiratory valve incl. valve membrane.
• Expiratory one-way valve.
The expiratory valve coil, mounted under the

expiratory cassette compartment, controls the valve

membrane in the cassette.

SVX9120X

Gas

modules

Connector

muff

O

2

 cell incl.

bacteria filter

Safety valve

Insp. pressure transducer

tube incl. bacteria filter

Temperature

sensor

Inspiratory

pipe

Expiratory cassette

SVX9122X

Содержание Servo i







































































Отзывы:

Нет отзывов