Siemens Servo i Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 70

Siemens Servo i Скачать руководство пользователя страница 22

Siemens-Elema AB

Description of functions

Servo

…

E382 E407E 061 01 01 02

3 - 6

3

Expiratory section

Functional Main Blocks diagram marking: “

E

”

The main block E

XPIRATORY

S

ECTION

conveys the

breathing gas from the patient breathing system to
the E

XPIRATORY

O

UTLET

. It comprises:

• Measurement of expiratory flow

• Connection for measurement of expiratory

pressure.

• Controlling element for the regulation of expiratory

pressure.

Expiratory cassette

The expiratory gas conveying parts and PC 1786
E

XPIRATORY

C

HANNEL

C

ASSETTE

are integrated into one

part – the E

XPIRATORY

C

ASSETTE

– which can be easily

removed for cleaning or exchange. See Servo

…

Ventilator System – User’s manual.

The expiratory cassette can be interchanged between
different Servo

…

systems. Always perform a Pre-use

check after exchanging the expiratory cassette.

An ID PROM is integrated into each expiratory
cassette. Its ID information and remaining lifetime can
be read by the Servo

…

System.

Expiratory inlet
22 mm / 10 mm tube connector for the expiratory
tube of the patient breathing system. The inlet is
designed to make condensed water drip out and
allow use of a water trap for such water to be
collected. Expiratory inlet bacteria filter can be
connected to protect the cassette from contamination.

Heating foil
An electrical H

EATING

F

OIL

applied on the outside of the

expiratory pipe where the U

LTRASONIC

F

LOWMETER

is

situated. The purpose of the H

EATING

F

OIL

to reduce

condensation and maintain a stable temperature in
the expiratory gas.

Ultrasonic flowmeter
The U

LTRASONIC

F

LOWMETER

is a measuring device for

the expiratory gas flow, using ultrasound technique
with two ultrasonic transducers/recievers.
The measuring process is controlled from the main
block PC 1784 E

XPIRATORY

C

HANNEL

.

The left hand side transducer is sending out ultrasonic
sound that is reflected against the inner wall of the
expiratory channel. The ultrasonic sound is recieved
by the right hand side transducer now acting as a
reciever. The time from sending to recieving
ultrasonic sound in downstream expiratory gas flow is
measured.

Then the right hand side transducer (earlier recieving)
is sending out ultrasonic sound upstream the
expiratory gas flow. The ultrasonic sound is recieved
by the left hand side transducer now acting as a
reciever. The time from sending to recieving
ultrasonic sound in upstream expiratory gas flow is
measured.

The time difference between the downstream and
the upstream time measurements provides flow
information.

A temperature sensor inside the cassette measures
the expiratory gas temperature. This temperature
measurement is also used when calculating the
expiratory flow.

SVX9121X

Expiratory pressure

tube connector

Bacteria

filter

Heating

foil

PC 1786

Expiratory

channel cassette

Ultrasonic

transducer

Ultrasonic

transducer

Inlet

Outlet

SVX9143X

«
...
20
21
22
23
24
...
»

Содержание Servo i







































































Отзывы:

Нет отзывов