Siemens Servo i Скачать руководство пользователя страница 10

Страница: 10 / 70

Siemens-Elema AB

Introduction

Servo

…

E382 E407E 061 01 01 02

2 - 2

Main units

The Servo

…

System is available in different main

configurations:
• Infant
• Adult
• Universal
These main configurations are as standard equipped

with a number of ventilation modes suitable for each

patient category. Further ventilation modes can be

installed via software option upgrades.
The Servo

…

System can be divided into the following

main units:
• User Interface
• Patient Unit
The Control cable connects the User Interface and the

Patient Unit.
These main units are mounted onto the Servo

…

Mobile

cart which is the main body of the system.

A number of optional equipment can also be

incorporated in the Servo

…

System. Examples on such

optional equipments are:
• Servo Ultra Nebulizer, Servo

…

• Servo

…

Holder for the Patient Unit.

• Gas trolley for backup gas cylinders.
• Gas cylinder restrainer for backup gas cylinders.
• IV Pole, Servo

…

• User Interface panel cover.
• Battery module, Servo

…

• Support Arm 177.
• Servo Humidifier.
• Humidifier Holder, Servo

…

Patient Unit

User Interface

Servo

…

Mobile Cart

Содержание Servo i







































































Результаты поиска

Содержание Servo i

Отзывы:

Siemens Servo i, Руководство по обслуживанию, Страница: 10 / 70

Результаты поиска

Содержание Servo i

Отзывы: