manualshive.com logo in svg

Siemens Servo i, Руководство по обслуживанию, Страница: 51 / 70

Поделиться
Скачать
Siemens Servo i Скачать руководство пользователя страница 51

E382 E407E 061 01 01 02

Siemens-Elema AB

Servo

…

Troubleshooting

6 - 7

6

Technical error codes

The table below shows recommended actions in case

of Technical error alarms.

Error

code

Error message / Possible cause

Recommended action

Monitoring

1

POWER_FAILURE_MINUS_12_VOLTS_
TOO_LOW

1.

 

Check status of external battery (if
connected).

2.

 

Replace PC1778 Standard connectors &
DC/DC.

2

POWER_FAILURE_MINUS_12_VOLTS_
TOO_HIGH

1.

 

Replace PC1778 Standard connectors &
DC/DC.

3

POWER_FAILURE_12_VOLTS_TOO_LOW

1.

 

Check status of external battery (if
connected).

2.

 

Replace PC1778 Standard connectors &
DC/DC.

4

POWER_FAILURE_12_VOLTS_TOO_HIGH

1.

 

Replace PC1778 Standard connectors &
DC/DC.

5

POWER_FAILURE_24_VOLTS_TOO_LOW

1.

 

Replace PC1778 Standard connectors &
DC/DC.

2.

 

Replace gas modules.

6

POWER_FAILURE_24_VOLTS_TOO_HIGH

1.

 

Replace PC1778 Standard connectors &
DC/DC.

7

INSP_VALVE_RANGE_ERR

1.

 

Replace PC1771 Control.

2.

 

Replace PC1772 Monitoring.

3.

 

Replace gas modules.

8

TECH_ERR_INSP_PAUSE_HOLD_TIME_

EXCEEDED

1.

 

Replace PC1771 Control.

9

TECH_ERR_EXP_PAUSE_HOLD_TIME_
EXCEEDED

1.

 

Replace PC1771 Control.

10

VALVES_DISABLED

1.

 

Replace PC1784 Expiratory channel.

2.

 

Replace PC1771 Control.

3.

 

Replace PC1778 Standard connectors &
DC/DC.

11

SAFETY_VALVE_OPEN

1.

 

Check inspiratory channel

2.

 

Replace safety valve pull magnet.

3.

 

Replace PC1784 Expiratory channel.

12

BRE_NODE_DISCON

1.

 

Replace PC1771 Control.

13

BRE_NODEID_CONFLICT

N/A

14

PANEL_NODE_DISCON

1.

 

Check control cable

2.

 

Replace PC1777 Panel.

15

PANEL_NODEID_CONFLICT

N/A

Some of the Error codes are intended only for R&D,

not for field service. If so, the text ”N/A” is stated in

the ”Recommended action”-column.

Содержание Servo i







































































Отзывы:

Нет отзывов