Siemens Servo i Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 70

Siemens Servo i Скачать руководство пользователя страница 42

Siemens-Elema AB

Service procedures

Servo

…

E382 E407E 061 01 01 02

5 - 8

5

Menu key

The ”Menu” function is a useful tool for the hospital
Biomeds as well as for the Siemens CSE (Customer
Service Engineer). There are no locked functions
within the Menu, all users have access to all
functions. However, the ”Biomed” submenu is
intended only for Technical Personnel.

Menu flowchart

Pressing the fixed key ”Menu” will open the ”Menu”
window on the User Interface. Possible selections in
this window, as described in the flowchart, are:

• Alarm

• Complience compensation

• Copy data

• Biomed

• Panel lock

• Change patient category (available only in ventilation

mode).

Biomed

Of the possible selections in the ”Menu” window,
the ”Biomed” menu will be of main interest for the
hospital Biomed and for the Siemens CSE.

Service

Event Log:

Displays log lists. Useful during troubleshooting.

Service Log:

Displays log lists. Useful during troubleshooting.

Report PM:

This button must be pressed when a Preventive
Maintenance has been performed. This will reset the
timer that indicates operating hours until next
Preventive Maintenance.

Panel

lock

General

Units

Adult alarm limits

Infant alarm limits

Displayed values

Displays the default user
configuration.

Locks all user input functions on the control unit.
Press "Main screen" fixed key to unlock.

View configuration

Adult alarm limits

Infant alarm limits

Displayed values

User default configuration setup.

Date and time setup.

Edit configuration

Set date and clock

Biomed

Service

Event log

Alarms

Ventilator settings

Apnea periods

Immediate functions

Displays Event logs.

Possible selections:

•

Latest logs

•

Selected time interval.

Service log

Report PM

Technical alarms

Test results

Preventive Maintenance

Service report history

Displays Service logs.

Possible selections:

•

Latest logs

•

Selected time interval.

Enters Date for a performed Preventive
Maintenance into the Service Log.

Alarm

Profile

Compliance

compensation

Copy

data

History

Alarm profile setup.
Possible selections:

•

Pressure alarm (Upper)

•

Minute Volume alarm (Lower and Upper)

•

Respiratory Rate alarm (Lower and Upper)

•

End Expiratory Pressure alarm (Lower)

•

Alarm sound level (20_100%).

Copy data to PC Card.
The following data is copied:

•

Event log

•

Trends

•

Pre-use check log.

Displays a date and time stamped Alarm history log.

Silence or pre-silence alarms for two minutes.
Same function as the fixed key .

The calculation of the circuit Compliance value is
performed during Pre-use check.
The calculated value is displayed in the window. To
activate or to deactivate select the appropriate soft key.

Menu

Change pat.

category

Available only in Servo-i Universal. Switches between
Adult and Infant patient category (only in running mode).

«
...
40
41
42
43
44
...
»

Содержание Servo i







































































Отзывы:

Нет отзывов