Siemens Servo i Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 70

Siemens Servo i Скачать руководство пользователя страница 36

Siemens-Elema AB

Service procedures

Servo

…

E382 E407E 061 01 01 02

5 - 2

5

Software installation

General

• Before starting any software upgrade or update,

check the version of the installed Servo

…

system

software (see System version in the Status
window) and the version of the Servo

…

system

software stored on the PC Card. It is not
recommended to install Servo

…

system software

with lower version number than already installed in
the Servo

…

.

• After any installation, maintenance or service

intervention in the Servo

…

Ventilator System,

perform a ”Pre-use check” according to instructions
in the Servo

…

Ventilator System

– User's manual.

• To insert / remove the PC Card:

1. Open the slot cover.

2. Insert and gently push

the PC Card in place.

3. Press the eject button

and pull out the PC Card.

Software information

There are two different intentions for software
installation:

Option upgrade

An option upgrade will change the function of the
Servo

…

Ventilator System, e. g. change patient

category configuration and/or add new ventilation
modes. An option upgrade is individually created for
each ventilator and can only be installed on this
ventilator. Serial number of the ventilator must be
stated when ordering an option upgrade.

Option upgrade is distributed on an Option card. As
the option upgrade will change the functions of the
ventilator, a new Servo

…

Ventilator System – User's

manual will be enclosed. Option upgrades for several
Servo

…

can be distributed on one Option card. If so, a

corresponding number of User's manuals will be
enclosed.

System software update

A system software update will install a new system
software version in the Servo

…

Ventilator System.

It will not change the configuration of the ventilator.
System software updates are not dependent on the
serial number of the ventilator.

System software update is distributed on an S/W
version update card.

Note

: As an option upgrade may require a new

system software version, the Option card will also
contain this system software. A system software
update will then be performed during the option
upgrade.

«
...
34
35
36
37
38
...
»

Содержание Servo i







































































Отзывы:

Нет отзывов