manualshive.com logo in svg

Siemens Servo i, Руководство по обслуживанию, Страница: 11 / 70

Поделиться
Скачать
Siemens Servo i Скачать руководство пользователя страница 11

E382 E407E 061 01 01 02

Siemens-Elema AB

Servo

…

Introduction

2 - 3

2

User Interface

The User Interface can be mounted onto the Mobile

cart but can also easily be removed from the cart and

mounted on the bed post or table/shelf. The User

Interface can be rotated and tilted into a suitable

position. Locking levers, mounting devices and some

other items are shown in the illustration above.
1. Loudspeaker
2. Cable reel
3. PC Card slot with slot cover
4. Locking arm, rotation
5. Locking screw, alternative mounting
6. Panel holder
7. Control cable
8. Connection for PC, service port
9. On/Off switch
10. Locking arm, tilting.
For further information regarding the User Interface

controls, refer to the User's manual.

When the front panel section is removed from the

rear cover, the following parts are accessible:
• Touch screen assembly, front cover frame included.
• TFT Display including lamps.
• PC board Backlight inverter.
• PC 1777 Panel including PC Card slot.
• Loudspeaker.
• Main rotary dial (rotary encoder with switch).
• Direct access controls (rotary encoder).

SVX9100X

Loudspeaker

TFT Display

PC 1777

Panel

PC Card-

slot

Main rotary

dial

Direct access

controls

Backlight

inverter

Touch screen

assembly

Содержание Servo i







































































Отзывы:

Нет отзывов