Siemens Servo i Скачать руководство пользователя страница 13

Страница: 13 / 70

E382 E407E 061 01 01 02

Siemens-Elema AB

Servo

…

Introduction

2 - 5

When the Patient Unit front cover is removed, the

following parts are accessible:
• PC 1772 Monitoring.
• PC 1771 Control.
• PC 1784 Expiratory channel with the two connected

PC 1781 Inspiratory and Expiratory Pressure

Transducers.

• Expiratory valve coil.
• Plug-and-Play Module incl. PC 1775 Plug-and-Play

back-plane.

• AC/DC Converter.
• Internal fan.
• Mains supply inlet.
• PC 1778 Standard connectors & DC/DC.

• The PC boards, as listed above, are connected to

the PC 1770 Main back-plane.

• The gas modules, the O

cell and the safety valve

pull magnet are connected to the PC 1780 Pneu-

matic back-plane.

Plug & Play

Module incl.

PC 1775

Plug and Play

back-plane

PC 1778

Standard

Connectors

& DC/DC

SVX9101X

PC 1771

Control

PC 1784

Expiratory

channel

Expiratory

valve

coil

AC/DC

Converter

PC 1772

Monitoring

Internal

fan

Mains

supply

inlet

PC 1781

Exp. press.

transducer

PC 1781

Insp. press.

transducer

SVX9118X

PC 1770

Main back-plane

PC 1780

Pneumatic back-plane

Содержание Servo i







































































Результаты поиска

Содержание Servo i

Отзывы:

Siemens Servo i, Руководство по обслуживанию, Страница: 13 / 70

Результаты поиска

Содержание Servo i

Отзывы: