Siemens MOTOX BA 2010 страница 81 Скачать руководство пользователя | Manualshive

Страница: 81 / 124

background image

BA 2010
Operating Instructions, 02/2018, A5E38093846A/RS-AC

79

Disposal

9

WARNING

Incorrect used oil disposal
Incorrect disposal of used oil is a threat to the environment and health.
After use, oil must be taken to a used oil collection point. The addition of foreign material

such as solvents, and brake and cooling fluid is prohibited.
Avoid prolonged contact with the skin.

Empty the used oil from the gearbox. The used oil must be collected, stored, transported and

disposed of in accordance with regulations. Do not mix polyglycols with mineral oil. Dispose

of polyglycols separately.
Please observe country-specific laws. Under German law, to allow optimal treatment of the

oil (§4 VI Used Oil), oils with different disposal codes must not be mixed with one another.
Collect and dispose of used oil in accordance with regulations.
Remove oil spillages immediately with an oil-binding agent in compliance with environmental

requirements.
Dispose of the housing parts, motor parts, gear wheels, shafts and roller bearings of the

geared motor as scrap metal.
The worm wheels are made partly from non-ferrous metal. Dispose of them accordingly.
Dispose of packaging material in accordance with regulations.

Table 9- 1

Disposal codes for gear oils

Type of oil

Designation

Disposal code

Mineral oil

CLP ISO VG220

13 02 05

Polyglycols

CLP ISO PG VG220,

CLP ISO PG VG460,

CLP ISO H1 VG460

13 02 08

Polyalphaolefins

CLP ISO PAO VG68,

CLP ISO PAO VG220

13 02 06

Biologically degradable oils

CLP ISO E VG220

13 02 07

«
...
79
80
81
82
83
...
»

Содержание MOTOX BA 2010





























































































































Отзывы:

Нет отзывов

Похожие инструкции для MOTOX BA 2010

Бренд: ZOLL Страницы: 84

Бренд: Kaivac Страницы: 29

Бренд: MacDon Страницы: 65

Бренд: KaVo Страницы: 16

Бренд: Keithley Страницы: 42

Бренд: Facsimile Страницы: 16

Бренд: JB-Lighting Страницы: 60

Бренд: Bacharach Страницы: 48

Бренд: Xiitech Страницы: 6

NI VISION PCI-8254R

Бренд: National Instruments Страницы: 13

NI VISION PCI-8254R

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 39

Бренд: National Instruments Страницы: 65

Бренд: haacon Страницы: 59

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

Бренд: Park House Healthcare Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды