Siemens MOTOX BA 2010 Скачать руководство пользователя страница 24

Страница: 24 / 124

Incoming goods, transport, and storage

3.2 Transport

BA 2010

Operating Instructions, 02/2018, A5E38093846A/RS-AC

3.2

Transport

3.2.1

General information on transport

NOTICE
The use of force will damage the gearbox or geared motor
Transport the gearbox or geared motor carefully. Avoid knocks.
Before putting the drive into operation, remove any transport fixtures and keep them safe or

render them ineffective. You can then use them again for transporting further items or you

can apply them again.

Different forms of packaging may be used, depending on the size of the gearbox or geared

motor and the method of transport. Unless contractually agreed otherwise, the seaworthy

packaging complies with HPE Packaging Guidelines (Bundesverband Holzpackmittel

Paletten Exportverpackungen e.V., the German Federal Association for wooden packaging,

pallets, and export packaging).
Note the symbols which appear on the packaging. These have the following meanings:

This way up

Center of gravity

Fragile

Do not use hand hook

Keep dry

Attach here

Keep cool

Содержание MOTOX BA 2010





























































































































Результаты поиска

Содержание MOTOX BA 2010

Отзывы:

Siemens MOTOX BA 2010, Руководство по эксплуатации, Страница: 24 / 124

Результаты поиска

Содержание MOTOX BA 2010

Отзывы: