manualshive.com logo in svg

Siemens MOTOX BA 2010, Руководство по эксплуатации, Страница: 52 / 124

Поделиться
Скачать
Siemens MOTOX BA 2010 Скачать руководство пользователя страница 52

Commissioning 

 

5.3 Vent filter 

 

BA 2010 

50

 

Operating Instructions, 02/2018, A5E38093846A/RS-AC 

5.3

 

Vent filter 

Vent filter without securing clip 
In the case of gearboxes with housing ventilation, the necessary vent filter or pressure 

breather valve without a securing clip is delivered separately. They must be replaced with 

the appropriate vent plug before starting up the gearbox. 

 

Observe the symbol in the type of construction diagrams, see Mounting positions (Page 87): 

 

 

Ventilation 

Procedure 

1.

 

Unscrew the vent plug. 

2.

 

Seal the gearbox with the vent filter or the pressure breather valve without securing clip. 

You have now replaced the vent filter or pressure breather valve with the vent plug without 

the securing clip. 

Pressure breather valve with securing clip 
The pressure breather valve with securing clip 

①

 is fitted to gearboxes which require 

housing ventilation. 

 

Figure 5-1 

Pressure breather valve with securing clip 

Remove the transport fixture by pulling the securing clip 

①

 in the direction of the arrow. 

5.4

 

Gearbox with backstop (optional) 

 

 

NOTICE 
Running in the wrong direction of rotation can damage the geared motor 
Check the direction of rotation before starting up. 
Turn the input side or motor over manually. 
Use the phase sequence to check the direction of motor rotation and swap the two external 

conductors if necessary. 

 

Содержание MOTOX BA 2010





























































































































Отзывы:

Нет отзывов