Siemens MOTOX BA 2010 Скачать руководство пользователя страница 60

Страница: 60 / 124

Service and maintenance

8.1 General notes about maintenance work

BA 2010

Operating Instructions, 02/2018, A5E38093846A/RS-AC

Measure

Interval

Description of work

Check the oil level sensor.

Regularly and after oil changes. Checking the oil level sensor

(optional) (Page 75)

Check the oil quality.

Every 6 months.

Checking the oil quality

(Page 64)

First oil change after

commissioning.

After approximately

10000 operating hours or at the

latest after 2 years.

Checking and changing

lubricants (Page 59)

Subsequent oil changes.

Every 2 years or

10000 operating hours

Visual inspection of the gearbox

and shaft sealing ring for leaks.

After the first day, thereafter

monthly.

Checking the gearbox for leaks

(Page 74)

Clean the gearbox ventilation

and replace if necessary.

Depending on the degree of

pollution, at least every

6 months.

Cleaning the vent filter

(Page 75)

Clean the gearbox.

Cleaning the gearbox

(Page 76)

Check the friction clutch and

adjust if necessary.

After 500 hours, thereafter once

a year and after every blockage.

Maintenance of the friction

clutch (Page 77)

Check the coupling.

For the first time after 3 months. Please refer to the separate

operating instructions.

Complete inspection of the

geared motor.

Every 12 months.

Inspecting the gearbox

(Page 77)

Check that fastening bolts on

gearboxes and add-on elements

are securely tightened. Check

that covers and plugs are

securely fastened.

After 3 hours, regularly

thereafter.

Checking tightness of fastening

bolts (Page 76)

Change the roller bearing

grease.

When the oil is changed.

Change the roller bearing

grease (Page 69)

Replace the bearing.

Replace bearings (Page 73)

Check the rubber buffers on the

torque arms.

Every 6 months.

Torque arms with shaft-mounted

gearboxes (Page 46)

With synthetic oils, the intervals can be doubled. The data specified is valid for an oil temperature

of +80° C. See the figure titled "Guide values for oil change intervals" for the intervals for other

temperatures.

Содержание MOTOX BA 2010





























































































































Результаты поиска

Содержание MOTOX BA 2010

Отзывы:

Siemens MOTOX BA 2010, Руководство по эксплуатации, Страница: 60 / 124

Результаты поиска

Содержание MOTOX BA 2010

Отзывы: