Siemens MOTOX BA 2010 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 124

Siemens MOTOX BA 2010 Скачать руководство пользователя страница 42

Installation

4.10 Removing and installing the shaft-mounted gearbox

BA 2010

40

Operating Instructions, 02/2018, A5E38093846A/RS-AC

4.10.2.2

Removing the hollow shaft with parallel key

WARNING

Inadequately secured gearboxes or geared motors can break loose
Before driving out the machine shaft, fasten a suitably dimensioned means of absorbing

load to the gearbox.
Slightly pretension the drive element so that the gearbox does not drop into the drive

element when the insert shaft is released.

NOTICE
Subjecting stress to the hollow shaft causes bearing failure
It is essential to prevent misalignment when removing the unit.

NOTICE
Excessive forces during removal
Excessive forces can occur during removal of the hollow shaft via the housing.
Stresses in the hollow shaft can lead to bearing failure and damage to the gearbox housing.

Note
If frictional corrosion has occurred on the seat surfaces, use rust solvent to facilitate the

removal of the gearbox. Allow the rust solvent to work in sufficiently.

①

Disk

②

Threaded block

③

Parallel key

④

Hexagon nut

⑤

Threaded spindle

Figure 4-9

Removing the hollow shaft with parallel key

Items

①

to

⑤

are not included in the scope of supply.

«
...
40
41
42
43
44
...
»

Содержание MOTOX BA 2010





























































































































Отзывы:

Нет отзывов