Siemens Flender H2NV Series Скачать руководство пользователя страница 56

Страница: 56 / 62

56 / 62

BA 5060 EN 04/2011

10.2.5

Clean fan and gear unit

•

The instructions in item 5.8.1 must be observed!

Fig. 23:

Gear unit fitted with fan

Fan

Cover plate of the fan

A detailed view of the gear unit can be obtained from the drawings in the gearunit documentation.

•

Unscrew safety grid from the motor bell housing.

•

Demount the cover plates.

•

Using a stiff brush, remove any dirt adhering to the fan wheel, cover plates and safety grid.

•

Remove any corrosion.

•

Refit the cover plates.

•

Screw the safety grid to the motor bell housing using the fastening bolts.

It must be ensured that the cover plates are correctly fastened. The fan must not come
into contact with the cover plates.

To prevent the buildup of dust on the gear unit, cleaning must be done in accordance
with operating conditions.

The gear unit must not be cleaned with highpressure cleaning equipment.

Содержание Flender H2NV Series































































Результаты поиска

Содержание Flender H2NV Series

Отзывы:

Siemens Flender H2NV Series, Руководство по сборке и эксплуатации, Страница: 56 / 62

Результаты поиска

Содержание Flender H2NV Series

Отзывы: