Siemens Flender H2NV Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 62

Siemens Flender H2NV Series Скачать руководство пользователя страница 47

BA 5060 EN 04/2011

9.

Faults, causes and remedy

Observe the instructions in section 3, "Safety instructions", and in section 10, "Maintenance and repair"!

9.1

General information on faults and malfunctions

Faults and malfunctions occurring during the guarantee period and requiring repair work on the
gear unit must be carried out only by Siemens customer service.
In case of faults and malfunctions occurring after the guarantee period and whose cause
cannot be precisely identified, we advise our customers to contact our customer service.

Siemens will not be bound by the terms of the guarantee or otherwise be responsible
in cases of improper use of the gear unit, modifications carried out without Siemens’
agreement or use of spare parts not supplied by Siemens.

To remedy faults and malfunctions, the gear unit must always be taken out of service.
Secure the drive unit to prevent it from being started up unintentionally.
Attach a warning notice to the start switch.
In addition the gear unit must be secured to the fan at the output side in such a manner
that the fan cannot drive the gear unit.

9.2

Possible faults

Table 11:

Faults, causes and remedy

Faults

Causes

Remedy

Changes in gear noise.

Damage to gear teeth.

Excessive bearing play.

Bearing defective.

Overrunning noise caused by the
frequencyconverter operation.

Contact Customer Service.
- Check all toothed components

and replace any damaged parts.

Contact Customer Service.
- Adjust bearing backlash.

Contact Customer Service.
- Replace defective bearings.

Contact Customer Service.
- Check motor control.

Loud noises in the area of the
gearunit fastening.

Gearunit fastening has worked
loose.

Tighten bolts / nuts to specified
torque.
Replace damaged bolts / nuts.

Increased temperature at the
bearing points.

Oil level in housing too low.

Oil too old.

Mechanical oil pump defective.

Bearing defective.

Check oil level at room temperature
and, if necessary, top up oil.

Contact Customer Service.
- Check date of last oil change.

Contact Customer Service.
- Check that oil pump is working

correctly.

- Repair or replace oil pump.

Contact Customer Service.
- Check and, if necessary,

replace bearings.

«
...
45
46
47
48
49
...
»

Содержание Flender H2NV Series































































Отзывы:

Нет отзывов