Siemens Flender H2NV Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 62

Siemens Flender H2NV Series Скачать руководство пользователя страница 24

BA 5060 EN 04/2011

5.6.3

Protection against dry running

In order to safely avoid dry running of the shaft sealing ring arranged at the top, a grease filling (4) and
a ring (3) are provided above the shaft-sealing ring (2). In such case, a shaft-sealing ring with no additional
dust lip is applied. The ring (3) is fitted with a set screw (1) on the input shaft and prevents grease from
escaping upwards. The ring (3) rotates contactless in the housing cover, during operation.

2

1

4

3

Fig. 10:

Protection against dry running

1

Set screw

3

Ring

2

Radial shaftsealing ring

4

Grease filling

5.6.4

Taconite seal

Taconite seals have been specially developed for use in a dusty environment. The
penetration of dust is prevented by a combination of three sealing elements
(radial shaftsealing ring, lamellar seal and greasecharged labyrinth seal).

1

2

3

4

Fig. 11:

Taconite seal

1

Radial shaftsealing ring

3

Greasecharged labyrinth seal, rechargeable

2

Lamellar seal

4

Flat grease nipple AM10x1 to DIN 3404

A detailed view of the gear unit can be obtained from the drawings in the gearunit documentation.

The specified frequencies must be observed (see section 10, "Maintenance and
repair") for recharging the labyrinth seals with grease.

«
...
22
23
24
25
26
...
»

Содержание Flender H2NV Series































































Отзывы:

Нет отзывов