manualshive.com logo in svg

Siemens Flender H2NV Series, Руководство по сборке и эксплуатации, Страница: 48 / 62

Поделиться
Скачать
Siemens Flender H2NV Series Скачать руководство пользователя страница 48

48 / 62

BA 5060 EN 04/2011

Faults

Remedy

Causes

Gear unit is oiled up.

Inadequate sealing of housing
covers and/or joints.

Seal joints.

Oil leakage from the gear unit.

Inadequate sealing of housing
covers and/or joints.

Radial shaft­sealing rings
defective.

Check and, if necessary, replace
sealings. Seal joints.

Check radial shaft­sealing rings and,
if necessary, replace.

Grease escaping at the
output shaft.

Radial shaft­sealing rings
defective.

Check radial shaft­sealing rings and,
if necessary, replace.

Oil foaming in the gear unit.

Preservation agent not completely
drained.

Gear unit too cold in operation.

Water in oil.

Oil too old
(defoaming agent used up).

Unsuitable oils mixed up.

Oil change.

Shut down gear unit and have oil
degassed. Restart without cooling
water.

Test the oil, change oil if necessary.

Test the oil, change oil if necessary.

Test the oil, change oil if necessary.

Oil foams in sump.

Water in oil.

Gear unit exposed to cold air from
machine­room ventilator: Water
condensing.

Protect gear unit with suitable heat
insulation. Close air outlet or alter its
direction by structural measures.

Wet­air filter changes colour
from top to bottom.

Water in oil.

Contact Customer Service.
- Change oil.

Increased operating
temperature.

Oil level in housing too high.

Oil too old.

Oil badly contaminated.

Seriously contaminated oil filter.

Oil pump defective.

On gear units with fan: Suction
opening in air­guide cover and/or
gear­unit housing badly
contaminated.

Check oil level and, if necessary,
adjust.

Contact Customer Service.
- Check date of last oil change.

Contact Customer Service.
- Change oil.

Clean the oil filter.

Contact Customer Service.
- Check that oil pump is functioning

correctly.

- Repair or replace oil pump.

Clean air­guide cover and gear­unit
housing.

Содержание Flender H2NV Series































































Отзывы:

Нет отзывов