Siemens Flender H2NV Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 62

Siemens Flender H2NV Series Скачать руководство пользователя страница 38

BA 5060 EN 04/2011

7.

Startup

Observe the instructions in section 3, "Safety instructions"!

The gear unit must not be started up, if the required instructions are not available.

7.1

Procedure before startup

7.1.1

Removal of preservative agent

The location of the oildraining points is marked by an appropriate symbol in the dimensioned drawing in
the gearunit documentation (see item 5.2).

Oildraining point:

•

Place suitable containers under the oildraining points.

•

If necessary connect a maintenance hose.

•

Unscrew the oildrain plug or open the oildrain cock.

•

Remove remaining preservative agent and/or runningin oil from the gear unit using a suitable
container, unscrew any existing residualoil drain plugs, to do so.

•

Dispose of remaining preservative and/or runningin oil in accordance with regulations.

Any oil spillage must be removed immediately with an oilbinding agent.
The oil must not come into contact with the skin (e.g. the operator’s hands).
The safety notes on the data sheets for the oil used must be observed here!

•

Screw in oildrain plug or reclose oildrain cock.

•

Close any unscrewed residualoil drain plugs again.

A detailed view of the gear unit can be obtained from the drawings in the gearunit documentation.

«
...
36
37
38
39
40
...
»

Содержание Flender H2NV Series































































Отзывы:

Нет отзывов