Siemens FC300 Скачать руководство пользователя страница 209 | Manualshive

Страница: 209 / 518

Siemens FC300 Скачать руководство пользователя страница 209

10.3.2

Troubleshooting sensor-related problems

Incorrect and unstable measurements, especially at low flows, are typically a result of an

unstable zero point due to:
● Incorrect installation
● Bubbles in the liquid
● Vibrations/Cross talk
● Solid particles settling in the liquid
In the following a 4-step guide to troubleshooting is provided:

Step 1

Preliminary application inspection

Step 2

Zero point adjustment

Step 3

Measurement error calculation

Step 4

Application improvement

The guide will enable you to trace the reason for incorrect measurements and to improve the

application.

Step 1: Inspecting the application

Ensure that:
1. The sensor is installed as described in Installing/mounting (Page 37).
2. The sensor is located in a vibration-free position. Vibrations can disturb the sensor and

therefore cause measurement error.

Depending on application, you should furthermore ensure the following:
● Liquid application

Ensure that the sensor is filled with liquid and liquid only.

Air or gas bubbles in the liquid cause instability and can result in measurement errors.

Flush the pipe systems and the sensor for several minutes at maximum flowrate to remove

any air bubbles which may be present.

Note
The liquid must be homogeneous in order to measure with high accuracy. If the liquid

contains solid particles of greater density than the liquid, then these solids can settle,

especially at low flow rates, which will cause instability in the sensor and lead to

measurement errors.
For pastes or process fluids with suspended solids always orient the sensor vertically with

flow in upward direction to maintain solids suspension.

● Gas application

Ensure that the gas pressure/temperature conditions contain sufficient superheat to prevent

dewing or precipitation. If the gas contains vapor or droplets then these may precipitate,

causing instability.

Diagnosing and troubleshooting

10.3 Operation troubleshooting

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

209

«
...
207
208
209
210
211
...
»

Содержание FC300







































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов