Siemens Climatix Series Скачать руководство пользователя страница 76

Страница: 76 / 244

76 / 244

Siemens

Standard application AHU

CE1P3977en_02

Building Technologies

Functions

01.02.2010

5.8.4 Heizregister-Frostschutz

Frost protection type is enabled:

Master Index > Configuration > Configuration 2, Htg frost protect<> No

Master Index > Configuration > Configuration 2, Heating 2 frost protect <> No

– For heat demand frost controller > Heat demand heating controller ---> The out-

put follows the frost controller.

– For heat demand frost controller < Heat demand heat controller ---> The output

follows the heating controller.

– Frost control remains active when the plant is off. (Building Protection).

– Controller is disabled when the sensor fails.

– For the “Frost” state (frost detector is triggered), the pump starts, the heating

valve opens to 100% and the plant is shut down and locked.

Master Index > Unit > Temp control > Heating > Frost protection

Master Index > Unit > Temp control > Heating 2 > Frost protection

Parameter

Range

Function

Controller

0...100 [%]

Present value for the frost controlled. Go to con-

troller settings page.

Setpoint

-64...64 [°C]

– For one setpoint: Present setpoint for the frost

controller.

– For 2 setpoints: Present setpoint for the frost

controller, if the plant is

operating

Standby Setpoint

-64...64 [°C]

Present setpoint for the frost controller, if the

plant is

not operating

This value only exists on one of the following

settings is selected:

Master Index > Configuration > Configuration 2,

HtgFrost = Sensor2Spv oder 2Spv+Dtctr

5.8.5 Preheat heating register

Preheating is enabled:

Master Index > Configuration > Configuration 1, Heating = Yes+PreHeat

Master Index > Configuration > Configuration 1, Heating 2 = Yes+PreHeat
– The heating valve is 100% opened for the period "Pre htg on time" if the outside

air temperature is lower than "Outs air tmp X1" at plant start. The heating valve

then goes to the position defaulted by both auxiliary points and is released for

plant start.

– It assumes the present position after the complete heating controller is released.

– The function is blocked for the period "Min off time" after preheating is com-

pleted.

– The function is deactivated when the outside air temperature senor not activated

or fails.

Main Index > Unit > Temp control > Heating > Preheating

Main Index > Unit > Temp control > Heating 2 > Preheating

Parameter

Range

Mode

– On

– Off

Current status preheating.

Outs air tmp X1

-30.0...5.0 [°C]

Lower design temperature.

Prerequisite

Function

Parameter

Prerequisite

Function

Parameter

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 76

Содержание Climatix Series





















































































































































































































































Результаты поиска

Содержание Climatix Series

Отзывы:

Siemens Climatix Series, Основной документ, Страница: 76 / 244

Результаты поиска

Содержание Climatix Series

Отзывы: