Siemens Climatix Series Скачать руководство пользователя страница 45

Страница: 45 / 244

45 / 244

Siemens

Standard application AHU

CE1P3977en_02

Building Technologies

Functions

01.02.2010

The plant

night start

by temperature difference for cooling demand occurs when

the following conditions are met:

– Room tmp > Start stpt cooling und

– Timer Minimum off time = 0

The

shutdown

occurs for:

– Room tmp < Start stpt cooling - Hysteresis

The plant

night start

by temperature difference for heating demand occurs when

the following conditions are met:

– Room tmp > Start stpt heating und

– Timer Min off time = 0

The

shutdown

occurs for cooling demand occurs for:

Room tmp > Start stpt h Hysteresis

The function when the room temperature sensor (return air sensor) fails.

Main Index > Unit > Operating mode > Tmp start

Parameter

Range

Function

Start stpt cooling

-64.0….64.0 [°C]

Start temperature for cooling.

Cooling setpoint

-64.0….64.0 [°C]

Cooling setpoint.

Start stpt heating

-64.0…64.0 [°C]

Start temperature for heating.

Heating setpoint

-64.0….64.0 [°C]

Heating setpoint.

Hysteresis

0.1…64.0 [°C]

Shutdown hysteresis.

Minimum off time

0…999 [min]

Minimum switch-off time after active heating or cooling.

Min run time

0.0…..999.0 [min] Minimum runtime after a start.

5.2.8 Boost function (boost plant start)

Boost is enabled:

Main Index > Configuration > Configuration 2 >

Boost <> No

Boost ensures a comfortable room temperature when the plant is switched on nor-

mally.
The heating and or cooling start can be enabled separately:

Main Index > Configuration > Configuration 2 > Boost
The function can be implemented using a return air sensor if no room sensor is

available.

Boost

for cooling demand occurs when the following conditions are met:

– Room tmp > Start stpt c Hysteresis and

– Time to normal start via the time switch program < Compensation time

The

shutdown

occurs for:

– Room tmp < Start stpt cooling

Boost

for heating demand occurs when the following conditions are met:

– Room tmp < Start stpt heating - Hysteresis and

– Time to normal start via the time switch program < Compensation time

The

shutdown

occurs for:

– Room tmp > Start stpt heating

The function when the room temperature sensor (return air sensor) fails.

Cooling demand

Heating demand

Note

Parameter

Prerequisite:

Function

Cooling demand

Heating demand

Note

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 45

Содержание Climatix Series





















































































































































































































































Результаты поиска

Содержание Climatix Series

Отзывы:

Бренды по названию

Популярные бренды

Siemens Climatix Series, Основной документ

Результаты поиска

Содержание Climatix Series

Отзывы:

Бренды по названию

Популярные бренды