Siemens Climatix Series Скачать руководство пользователя страница 55

Страница: 55 / 244

55 / 244

Siemens

Standard application AHU

CE1P3977en_02

Building Technologies

Functions

01.02.2010

Max forcing

0...(100-Stage max.) [%]

0...(40'000-Stage max.) [l/s]

0...(5000-Stage max.) [Pa

Depends on control type (fan control mode <> Direct or

DirectVar): The maximum possible fan compensation is

derived from the following formula:

Stage max. + Max forcing - Stage x [%], [l/s], [Pa]

(See Fan compensation).

Min runtime

0…36000 [s]

Define the minimum runtime for the fan after a start.

Switch on

delay

0…36000 [s]

For supply air fan only!

Defines switch-on delay for the supply air fan after a ex-

haust fan start.

Start up delay

fdbk

0…36000 [s]

Defines the period after a fan start without feedback before

a feedback alarm is triggered. Jitter time is enabled exclu-

sively if the feedback is pending after this period.

Deviation

alarm

– Passive

– Active

Condition: Fan control mode <> Direct, DirectVar or

FixedSpd.

Present state for the setpoint/actual value monitoring of the

supply air pressure (or volume). Go to parameter page for

supply air monitoring.

– No alarm.

– Alarm pending.

Feedback can only be used as alarm, when Contact function = NO (Normally

Open) and the element is set to ON.

5.4.4 Summer/Winter compensation

– An outside air temperature sensor must be available:

Main Index > Configuration > Configuration 1 > Outside tmp sensor = Yes.

– Summer/winter compensation must be enabled:

Main Index > Configuration > Configuration 2 > Fancomp Outsidetmp = Yes.

•

Summer compensation

: Adjustment to setpoint relevant to control when the

outside air temperature is high during the summer.

•

Winter compensation

: Adjustment to setpoint relevant to control when the out-

side air temperature is low during the winter.

Note

Prerequisites

Function

Setpoint compensation

during summer

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 55

Содержание Climatix Series





















































































































































































































































Результаты поиска

Содержание Climatix Series

Отзывы:

Бренды по названию

Популярные бренды

Siemens Climatix Series, Основной документ

Результаты поиска

Содержание Climatix Series

Отзывы:

Бренды по названию

Популярные бренды