Siemens Climatix Series Скачать руководство пользователя страница 75

Страница: 75 / 244

75 / 244

Siemens

Standard application AHU

CE1P3977en_02

Building Technologies

Functions

01.02.2010

Parameter

Range

Function

Alarm

– OK

– Alarm

Current pump alarm state.

Go to page with digital input settings. For exam-

ple, you can set the time for jitter protection (De-

fault: 0 s).

Start up delay fdbk

0...36000 [s]

Defines the period after a pump start without

feedback before a feedback alarm is triggered.

Jitter time is enabled exclusively if the feedback

is pending after this period.

Off by fdbk alarm

– No

– Yes

Determines, in the event of a feedback fault,

whether a pump command is still pending or

whether to switch off the command.

Outs tmp start

-64...64 [°C]

The pump starts when the outside air tempera-

ture drops below this value. Heat is thus avail-

able immediately for heating (passive frost pro-

tection) when switching on the plant.

The function is disabled when no outside air

temperature is configured or the sensor fails.

Min run time

0...36000 [s]

Define the minimum runtime for the pump after a

start.

Feedback can only be used as alarm, when Contact function = NO (Normally

Open) and the element is set to ON.

5.8.3 Pump kick

Pump kick is enabled.

Main Index > Configuration > Configuration 2 > Heating pump = Yes+Kick

Main Index > Configuration > Configuration 2 > Heating 2 pump = Yes+Kick

The pump is switched on for a short period for longer idle periods. This prevents

lock up.

Main Index > Unit > Temp control > Heating > Pump

Main Index > Unit > Temp control > Heating 2 > Pump

Parameter

Range

Function

Kick date / time

Mo 00:00...So 23:29

Weekday and time for pump kick. Sets the weekday

(Mon...Sun) and time to run the pump kick. Examples:

Mon *:* Each Monday at midnight.

Sat 07:* Each Saturday at 7:00 am.

* *:*

Time is not relevant; the kick interval applies

accordingly.

Kick interval

0.0...36000.0 [h]

Idle time for pump kick. Set the idle time after which a

pump kick is run. Examples:

168

After 168 hours.

123.4

After 123 hours and 24 minutes.

Idle time is not relevant; kick date/time applies

accordingly.

Kick on time

0.0...36000 [s]

Set the period for the pump kick. Examples:

Period = 10 seconds.

Period = 1 controller cycle (ca. 150 ms).

Kick date/time = * *:* and kick interval = 0 --->

No pump kick is run.

Note

Prerequisite

Function

Parameter

Note

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 75

Содержание Climatix Series





















































































































































































































































Результаты поиска

Содержание Climatix Series

Отзывы:

Бренды по названию

Популярные бренды

Siemens Climatix Series, Основной документ

Результаты поиска

Содержание Climatix Series

Отзывы:

Бренды по названию

Популярные бренды