Siemens Climatix Series Скачать руководство пользователя страница 120

Страница: 120 / 244

120 / 244

Siemens

Standard application AHU

CE1P3977en_02

Building Technologies

Communication

01.02.2010

Parameter

Range

Function

−

2 RU

ing 1 RU, 1snsr+RU or 2 RU, the interface to the

room unit connection is enabled.

Settings

Goes to page with all settings relevant to param-

eterizing room units.

Inputs

Go to page with temperature inputs.

Reset required !!

−



−

Execute

As a matter of principle, the controller must be

set after parameterization to assume the data.

Unit > System overview > Communication > Modbus

Parameter

Range

Function

Communication

−

Alarm

Status of Modbus communication.

Internal

−

Disable

−

Master

−

Slave

Generally enables internal MODBUS and func-

tion of MODBUS over RS485:

−

Internal interface is disabled.

−

Internal RS485 interface is master.

−

Internal RS485 interface is slave.

Internal Slave address

0…247

Controller address on the RS485 bus.

Internal settings

RS485

Go to parameter page for RS485 MODBUS in-

terface.

TCP/IP

−

Go to parameter page for TCP/IP settings.

Module1 Modbus

−

Go to parameter page for MODBUS interface on

module 1.

Module1 Modbus

−

Go to parameter page for MODBUS interface on

module 1.

Module1 Modbus

−

Go to parameterization page for MODBUS

interface on module 1.

Unit > System overview > Communication > Modbus > RS485

Parameter

Range

Function

−

Baud rate

−

2400

−

4800

−

9600

−

19200

−

38400

Transmission rate on bus. All participants must

have the same setting.

Parity

−

Even

−

Odd

−

None

Parity. All participants must have the same set-

ting.

Stop bit

−

One

−

Two

Number of stop bits. All participants must have

the same setting.

Delay time

0…2147483647 [ms]

Response telegram delay.

Parameter

Range

Function

Response timeout

0…2147483647 [ms]

Settings access time for master.

The master must undertake read access within this

period, otherwise an alarm is triggered (this func-

tion is not yet fully implemented).

Termination

−

Passive

Internal bus connection for the basis controller:

−

No bus terminating resistor.

MODBUS configuration

RS485 MODBUS

parameterization

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 120

Содержание Climatix Series





















































































































































































































































Результаты поиска

Содержание Climatix Series

Отзывы:

Бренды по названию

Популярные бренды

Siemens Climatix Series, Основной документ

Результаты поиска

Содержание Climatix Series

Отзывы:

Бренды по названию

Популярные бренды