Siemens 1PL622 Скачать руководство пользователя страница 21

Страница: 21 / 86

Description

2.5 Layout

A5E00264365A
Siemens AG Operating Instructions 2.02 1PL622

Securing the cooling capacity

CAUTION

Missing cover sheets can result in considerably reduced cooling capacity and thus cause

an inadmissible temperature rise within the motor.
Please ensure that the cover sheets are always mounted.

[ID: 312.01]

2.5.2

Drive

Description

The variable-speed, three-phase motors of the 1PL6 series are supplied with power by a

frequency converter.
[ID: 313]

2.5.3

Construction types

Further potential applications

The construction type of the motor is stated on the rating plate.

CAUTION

During transportation, motors must only be hoisted in a position corresponding to their

basic construction type.

Basic construction type acc. to

rating plate

Type

Other applications in construction

type

IM B3

1PL6 224…1PL6 228

IM B6, IM B7, IM B8,
IM V5, IM V6

IM B35 (1)

1PL6 224…1PL6 228

IM V36, IM V15

The maximum permissible speed for flange-mounted construction types (IM B5, IM V1, IM

V3) is restricted to 2500 rpm (see also "Planning Guide").

Note
For additional instructions and restrictions for construction types that do not correspond to

the basic type, please refer to the "Planning Guide".

Содержание 1PL622























































































Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды

Siemens 1PL622, Руководство по эксплуатации

Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды