Siemens 1PL622 Скачать руководство пользователя страница 60

Страница: 60 / 86

Maintenance

7.1 Maintenance

A5E00264365A

Siemens AG Operating Instructions 2.02 1PL622

Note
The shaft should rotate so that the new grease can be distributed throughout the bearing.

The bearing temperature rises sharply at first, then drops to the normal value again after the

excess grease has been displaced out of the bearing.

Arrangement of the grease nipples on motors with radial ventilation

ແ

ໂ

Figure 7-2

N-end end shield with grease nipples at N-end and D-end

①

Button head lubricating nipple to DIN 3404, size M10x1, non-drive end (NDE)

②

Button head lubricating nipple to DIN 3404, size M10x1, drive end (DE)

[ID: 969.01]

7.1.6

Cleaning

Cleaning the greasing channels and used grease chambers

The used grease collects outside each bearing in the used grease chamber of the outer

bearing cap. Remove the used grease when you replace a bearing.

Содержание 1PL622























































































Результаты поиска

Содержание 1PL622

Отзывы:

Siemens 1PL622, Руководство по эксплуатации, Страница: 60 / 86

Результаты поиска

Содержание 1PL622

Отзывы: