Siemens 1PL622 Скачать руководство пользователя страница 42

Страница: 42 / 86

Transport, assembly, and connection

3.3 Electrical connection

A5E00264365A

Siemens AG Operating Instructions 2.02 1PL622

NOTICE

Do not turn the Sensor Module with a pipe wrench or hammer or any similar tool as this

could damage the Sensor Module.
Turn the Sensor Module by hand.

Typical twisting moment:

4 ... 8 Nm

ແ

Figure 3-11 Sensor Module ① mounted on terminal box

NOTICE

Changing the cable outlet direction by any improper means will cause damage to the

connecting cables.
The permissible rotation range must not be exceeded. A maximum of ten changes to the

rotation angle of the Sensor Module are permissible within the rotation range.

[ID 964]

3.3.8

Connecting the temperature sensor

Connection

Connect the wires of the temperature sensor to the speed sensor connector with the aid of

connecting leads (see section entitled "Connecting the speed sensor").

Содержание 1PL622























































































Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды

Siemens 1PL622, Руководство по эксплуатации

Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды