Siemens 1PL622 Скачать руководство пользователя страница 49

Страница: 49 / 86

A5E00264365A
Siemens AG Operating Instructions 2.02 1PL622

Operation

5.1

Operation

Safety notes

WARNING

Please follow all instructions contained in the "Safety information and application

information (Page 7)" chapter of these operating instructions precisely and ensure that only

persons who have the necessary specialist know-how are entrusted to carry out work on

power installations.

WARNING

Rotating components
Covers prevent contact with live or rotating parts, or are used for proper air routing and thus

effective cooling of the motor.
Removing the covers during operation can result in death, serious injury, and property

damage.
Never open covers during operation.

CAUTION

Speed monitoring
The motor is designed for a certain speed range.
If a motor is operated at impermissible speeds damage to the winding, bearings, or

complete destruction of the motor can be the result.
Ensure that the speeds specified on the rating plate are not exceeded by appropriately

configuring controller and speed monitoring components.

Switching on

●

See the operating instructions of the frequency converter for switching on.

●

After starting the motor, observe it for a while to see if it is running smoothly and check

the monitoring devices.

Содержание 1PL622























































































Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды

Siemens 1PL622, Руководство по эксплуатации

Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды