Siemens 1PL622 Скачать руководство пользователя страница 59

Страница: 59 / 86

Maintenance

7.1 Maintenance

A5E00264365A
Siemens AG Operating Instructions 2.02 1PL622

K3N greases
WINTERSHALL Wiolub LFK 3

These greases have lithium soap as the thickening agent and mineral oil as the base oil.

They exceed the standard requirements of DIN 51825 in several important respects and are,

therefore, compatible with the specified regreasing intervals.

NOTICE

Never mix greases that have different thickening agents and base oils.

Initial lubrication

ESSO Unirex N grease is used for initial lubrication of the bearings (prior to delivery).

Lubricating using the regreasing device

ແ

ໂ

Figure 7-1

D-end and N-end end shields with grease nipples

①

Button head lubricating nipple to DIN 3404, size M10x1, drive end (DE)

②

Button head lubricating nipple to DIN 3404, size M10x1, non-drive end (NDE)

Clean the grease nipples at the DE and NDE.

Press in the type and quantity of grease specified (see lubrication instruction plate).

Содержание 1PL622























































































Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды

Siemens 1PL622, Руководство по эксплуатации

Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды