Siemens 1PL622 Скачать руководство пользователя страница 45

Страница: 45 / 86

A5E00264365A
Siemens AG Operating Instructions 2.02 1PL622

Start-up

4.1

Preparations

Safety note

WARNING

Only expert personnel should be entrusted with work on power installations.

Checking the insulation resistance

Note
There is no need to check the insulation resistance when commissioning. We only

recommend doing so after long storage or shutdown periods.
After long storage or shutdown periods, the insulation resistance of the windings must be

measured to ground with direct voltage.

WARNING

Hazardous voltage
During the measurement, and immediately afterwards, hazardous voltage levels are

applied on some of the terminals and they should not be touched. Touching live

components can be result in death or serious injury.
Never touch the terminals when measuring or immediately after the measurement.
Check the supply feeder cables connected in order to ensure that the line supply voltage

cannot be connected.

CAUTION

Before you begin measuring the insulation resistance, please read the manual for the

insulation resistance meter you are going to use.

●

Always measure the insulation resistance of the winding to the motor enclosure when the

winding temperature is between 20 and 30°C.

Содержание 1PL622























































































Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды

Siemens 1PL622, Руководство по эксплуатации

Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды