Siemens 1PL622 Скачать руководство пользователя страница 22

Страница: 22 / 86

Description

2.5 Layout

A5E00264365A

Siemens AG Operating Instructions 2.02 1PL622

Additional hoisting points for different construction types (option)

Additional hoisting points are provided for those construction types that differ from the basic

construction types (hoisting points (1), see Fig.).

ແ

Figure 2-4

View from above onto construction type IM B3

(1)

Hoisting points

[ID: 389.01]

2.5.4

Regulations

Overview

The motors comply with the following regulations under IEC EN 60034:

Table 2-3

Compliance with standards

Feature

Standard

Dimensions and operating performance

IEC/EN 60034-1

Degree of protection (1)

IEC/EN 60034-5

Cooling

IEC/EN 60034-6

Type of construction

IEC/EN 60034-7

Noise emission

IEC/EN 60034-9

Vibration severity levels

IEC/EN 60034-14

(1) See the rating plate for the degree of machine protection.

[ID: 319.01]

Содержание 1PL622























































































Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды

Siemens 1PL622, Руководство по эксплуатации

Результаты поиска

Содержание 1PL622

Отзывы:

Похожие инструкции для 1PL622

Бренды по названию

Популярные бренды