manualshive.com logo in svg

SICK ISD 230, Руководство по эксплуатации, Страница: 2 / 58

Поделиться
Скачать
SICK ISD 230 Скачать руководство пользователя страница 2

Operating Instructions

ISD 230/260/280 IR Data Transmission Systems

© SICK AG · Auto Ident · Germany · All rights reserved

8 008 207/30-11-2001

2

Quick Finder

Installation procedure (overview)

Installing the ISD 230 system

Two identical units from the ISD 230 series are required (e.g. 2 x ISD 230-

2111

).

1. Set the transmission frequency on each unit

See 

Chapter

 

5.1.2 Setting the transmission frequencies ................................... Page 22

2. Configure the data interface on each unit

(interface type and transfer rate)

See 

Chapter 5.1.3 Configuring the data interface ................................................. Page 24

3. Connect the units

(data interface and function interfaces)

See 

Chapter 5.1.4 Connector pin assignment ........................................................ Page 26

See 

Chapter 5.1.6 Connecting the data interface ................................................. Page 27

See 

Chapter 5.1.7 Connecting the functions interfaces ...................................... Page 30

4. Mount and align the units

See 

Chapter 4 Installation .............................................................................................. Page 16

5. Apply the 24 V DC supply voltage to both units

6. Check alignment

See 

Chapter 6.1. Switching on the units/fine adjustment .................................. Page 43

7.

Send data on electrical interface

See 

Chapter 6.2. Functional test of the data transmission ................................ Page 43

The ISD 230 is ready for operation!

Installing the ISD 260/280 system

Two different units are required from the same series (e.g. 1 x ISD 260-111

1

 and

1 x ISD 260-111

2

)

1. Configure the data interface on each unit

(interface type and transfer rate)

See 

Chapter 5.2.3 Configuring the data interface ................................................ Page 33

2. Connect the units

(data interface and function interfaces)

See 

Chapter 5.2.4 Pin assignment ............................................................................. Page 35

See 

Chapter 5.2.6 Connecting the data interface ................................................ Page 37

See 

Chapter 5.2.7 Connecting the functions interfaces ..................................... Page 40

3.

Mount and align the units

See 

Chapter 4 Installation .............................................................................................. Page 16

4. Apply the 24 V DC supply voltage to both units

5. Check alignment

See 

Chapter 6.1. Switching on the units/fine adjustment .................................. Page 43

6. Send data on electrical interface

See 

Chapter 6.2. Functional test of the data transmission ................................ Page 43

The ISD 260/280 is ready for operation!

ISD 230

ISD 260/ISD 280

Содержание ISD 230



























































Отзывы:

Нет отзывов