Sharp AR-FX11 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 116

background image

11

BEFORE USING THE FAX FUNCTION

1

AUDITING MODE

Accounts that can transmit faxes (up to 50) can be established and transmission time and other information can be
tracked for each account. The Acc. Usage List (page 95) can be printed out which shows the time used for
transmission and pages transmitted by each account.

• This function is enabled using "ACCOUNT CONTROL" and "ACCOUNT # SET" in the key operator programs.

(Page 98)

Using auditing mode

When auditing mode is turned on, the account number entry screen is displayed. Enter your account number
(five-digit identification number) as explained below before performing a fax operation.

1

Enter your account number (five
digits) with the numeric keys.

• As the account number is entered, the hyphens "-"

change to asterisks " ". If you enter an incorrect
digit, press the [C] key and re-enter the correct digit.

• After you enter your account number, the base

screen of fax mode appears. (Page 10)

2

When you have completed the fax
operation, press the [ACC.#-C] key
( ).

Enter your account
number.
ACCOUNT #:

-----

• If you enter an account number for copy

mode has also been programmed for fax
mode, you can change to fax mode after
completing the copy operation and
continue with the fax operation without
re-entering your account number.
If you enter an account number for copy
mode that has not been programmed for
fax mode, enter your account number for
fax mode after you press the [FAX] key to
change to fax mode.

• When "ACC. # SECURITY" in the key

operator programs (see the "Key
operator's guide" in the "Operation
manual (for general information and
copier)".) is enabled, the message
"Please see your key operator for
assistance." will appear for one minute in
the event that you enter an incorrect or
invalid account number three times in a
row. During that time operation of the
machine will not be possible.

ABC

DEF

JKL

GHI

MNO

TUV

PQRS

WXYZ

@.-_

FUNCTION

ACC. #-C

READ-END

OK

Enter your account
number.
ACCOUNT #:

---

Note

@.-_

FUNCTION

ACC. #-C

READ-E

Pegasus-E_Fax_Ex.book 11

ページ

２００４年１０月１８日　月曜日　午後８時４１分

«
...
11
12
13
14
15
...
»

Содержание AR-FX11





















































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-FX11

Бренд: Pfaff Страницы: 80

Sew Reach ABF Series

Бренд: Siruba Страницы: 74

Бренд: Pfaff Страницы: 54

Бренд: Singer Страницы: 34

Бренд: Kärcher Страницы: 55

Бренд: GBC Страницы: 43

Бренд: Racing Страницы: 22

Бренд: Parkeon Страницы: 127

Бренд: Duerkopp Adler Страницы: 84

Бренд: Janome Страницы: 40

Бренд: Opus Страницы: 16

Бренд: TIELBURGER Страницы: 44

Бренд: JUKI Страницы: 50

Бренд: JUKI Страницы: 72

Бренд: JUKI Страницы: 140

Бренд: BPS Страницы: 14

Бренд: Husqvarna Viking Страницы: 68

Бренд: ProLights Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды