Sharp AR-FX11 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 116

background image

87

TROUBLESHOOTING

7

XX-XX OK

When group dialling, broadcast transmission, or F-code relay request transmission
was performed,
xxx- : Indicates total number of transmissions.
xxx OK : Indicates completed transmissions.

NO S ADD FUNC

When an F-code transmission was attempted,
(1) The other machine did not have the F-code function.
(2) An F-code was not programmed in the other machine.

S ADD TX FAIL

When an F-code transmission was attempted,
(1) The sub-addresses did not match.
(2) The passcodes did not match.
(3) An F-code public box was set.

SA POLL ERR

When F-code public box transmission was attempted,
(1) The F-code public box specified by the sub-address did not exist.
(2) The sub-address specified a box other than an F-code public box.

PASSCODE# ERR

When F-code public box transmission was attempted,
(1) The passcodes did not match.

Reception result

Explanation

OK

Reception was completed successfully.

P. FAIL

The power was turned off or a power failure occurred.

MEMORY FULL

The image memory became full during substitute reception to memory.

LENGTH OVER

The transmitted document was over 1500 mm long and therefore could not be received.

NO RX ROLL

When polling was attempted,
(1) Your fax number (sender's number) was not programmed in your machine.
(2) Your fax number was not programmed as a polling passcode number in the other

machine.

RX NO POLL

When polling was attempted,
(1) The other machine did not have a polling function.
(2) The other machine did not have a document stored in polling memory.

ERRORxx xxxx

Line conditions prevented the reception from taking place normally.
First 2 digits of line error code: Error code from 00 to 31.
Last 4 digits of line error code: Code for use by service technicians.

XX-XX OK

When serial polling ended normally,
xxx- : Indicates total number of transmissions.
xxx OK : Indicates completed transmissions.

NO SA POLLING

When F-code polling was attempted,
(1) The other machine did not have an F-code polling memory function.
(2) An F-code was not programmed in the other machine.
(3) The other machine did not have a document stored in polling memory.

SA POL TX ERR

When F-code polling was attempted,
(1) The sub-addresses did not match.
(2) The passcodes did not match.
(3) The other machine's F-code memory boxes were for F-code relay request

transmission or for F-code confidential transmission.

S ADD RX FAIL

When F-code reception was attempted,
(1) The sub-addresses did not match or were not programmed.
(2) The passcodes did not match or were not programmed.
(3) An F-code polling memory box was programmed.

JUNK FAX ERR

Fax reception was denied by the reception denial function.

Sending result

Explanation

Pegasus-E_Fax_Ex.book 87

ページ

２００４年１０月１８日　月曜日　午後８時４１分

«
...
87
88
89
90
91
...
»

Содержание AR-FX11





















































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-FX11

Бренд: Garudan Страницы: 79

Бренд: Mannsberger Страницы: 22

Бренд: Riccar Страницы: 22

Бренд: Sinbo Страницы: 48

INNOVATECH P550Y

Бренд: Bartell Страницы: 20

FUTURA QUARTET SEQS-6000

Бренд: Singer Страницы: 112

Бренд: Tivax Страницы: 6

Advolution 2710

Бренд: Nilfisk-Advance Страницы: 60

artista 200 Embroidery

Бренд: Bernina Страницы: 43

Бренд: Muratec Страницы: 52

Auto-Logic KX-F115

Бренд: Panasonic Страницы: 34

Бренд: Panasonic Страницы: 74

Facsimile UF-590

Бренд: Panasonic Страницы: 162

DX 1000 - PanaFax B/W Laser Printer

Бренд: Panasonic Страницы: 200

Бренд: Panasonic Страницы: 215

Бренд: Panasonic Страницы: 224

Бренд: Panasonic Страницы: 256

Бренд: Panasonic Страницы: 255

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды