Sharp AR-FX11 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 116

background image

9

BEFORE USING THE FAX FUNCTION

1

(14) [MODE SELECT] keys (step 1 on page 18)

These are used these keys to change modes.

(15) [FAX] key/FAX indicator/LINE indicator/DATA

indicator

Press to switch to fax mode. The base screen of
fax mode will appear in the display.
The LINE indicator lights up during transmission
or reception of a fax. When a fax has been
received, the DATA indicator blinks. (When there
is fax transmission data in memory, the DATA
indicator lights up.)

(16) [PROGRAM] key (page 45)

Press this key to use a program.

(17) [RESOLUTION] key (page 15)

This key is used to select resolution and
exposure settings.

(18) [ADDRESS] key (page 21)

This key is used to search for a fax destination
that has been stored as an auto-dial number in
the address book.

(19) [BROADCAST] key (page 32)

This is used to perform a broadcast transmission.

(20) [ORIGINAL SIZE] key (page 14)

This is used to set the size of the original to be
faxed.

(21) [DUPLEX SCAN] key (page 22)

Press this key to use the duplex scan function.
(Only on models with a RSPF installed.)

(22) [SPECIAL FUNCTION] key

This key is used to select a special transmission
or reception function, configure function settings,
and to store auto-dial numbers.

(23) Arrow

keys

(

)

These are used to select items and move through
pages.

(24) [START] key (

)

This is used at the following times:
(1) When starting transmission
(2) When scanning an original
(3) When starting manual reception
(4) When configuring and storing settings

ABC

DEF

JKL

GHI

MNO

TUV

PQRS

WXYZ

@.-_

COPY EXPOSURE

PAPER

SELECT

COPY
RATIO

AUTO

IMAGE

OUTPUT

2-SIDED

COPY

SPECIAL FUNCTION

ACC. #-C

READ-END

SCAN

FAX

COLOUR MODE

PROGRAM

FORMAT

BROADCAST

OK

BACK

FAX STATUS

RESOLUTION ADDRESS

ORIGINAL SIZE DUPLEX SCAN

(2)

(3) (4)

(5)

(6)

(7) (8)

(16) (17) (18) (19) (20) (21)

(22)

(23)

(24)

• When the auto power shut-off function is

activated, All lights except the mode key
lights go off. For the information on the
auto power shut-off function, see the
"Operation manual (for general
information and copier)."

• For information on the keys and lights

which are used for the copy function and
other functions, see "Operation Panel" in
the manual for each function.

Note

Pegasus-E_Fax_Ex.book 9

ページ

２００４年１０月１８日　月曜日　午後８時４１分

«
...
9
10
11
12
13
...
»

Содержание AR-FX11





















































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-FX11

Бренд: Bally Страницы: 54

Бренд: GateWay Fax Systems Страницы: 13

Бренд: Janome Страницы: 82

Бренд: Janome Страницы: 112

Бренд: Singer Страницы: 12

Бренд: Pfaff Страницы: 88

Бренд: weasy Страницы: 75

Бренд: Titan Страницы: 33

Бренд: MyBinding Страницы: 3

FUTURA QUARTET SEQS-6000

Бренд: Singer Страницы: 112

Бренд: JUKI Страницы: 12

AMS-210E Series

Бренд: JUKI Страницы: 243

Бренд: Muratec Страницы: 138

Бренд: SCANMASKIN Страницы: 62

796.3155 series

Бренд: Kenmore Страницы: 34

Бренд: Oki Страницы: 116

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды