Sharp AR-FX11 Скачать руководство пользователя страница 58

Страница: 58 / 116

TRANSMISSION USING F-CODES

F-code confidential transmission

Follow steps 1 to 4 of "BASIC
PROCEDURE FOR SENDING FAXES"
(page 18) and then follow the steps
below.

Press the [SPECIAL FUNCTION] key.

When the [SPECIAL
FUNCTION] key is pressed, the
special function selection
screen appears.

Select "SENDING OPTIONS" with the
[

] or [

] key.

Press the [OK] key.

Select "SUB ADDRESS TX" with the
[

] or [

] key.

Press the [OK] key.

Enter the fax number of the other
machine with the numeric keys, or
press a Rapid key, or dial a Speed Dial
number (a group key cannot be used).

To clear a mistake when
entering a number with the
numeric keys, press the [C] key
to clear one digit at a time.

A destination selected with a Rapid key or Speed Dial
number is indicated by an icon and a number. To clear
an entry, press the [C] key.

Press the [OK] key.

Enter the sub-address (maximum 20
digits) with the numeric keys.

• Characters that can be entered are numbers, "#",

and spaces. However, the initial character cannot be
a space.

• If you make a mistake, press the [C] key and re-enter

the correct digit(s).

• If you specified a Rapid key or Speed Dial number in

step 7 that has a sub-address programmed, the
sub-address will appear. Go to the next step without
entering a sub-address.

Press the [OK] key.

Enter the passcode (maximum 20
digits) with the numeric keys.

• Characters that can be entered are numbers, "#",

and spaces. However, the initial character cannot be
a space.

• If you make a mistake, press the [C] key and re-enter

the correct digit(s).

• If you specified a Rapid key or Speed Dial number in

step 7 that has a passcode programmed, the
passcode will appear. Go to the next step without
entering the passcode.

Press the [OK] key.

Press the [START] key (

• Scanning begins.
• If you are scanning from the document glass and

have another page to scan, change pages and press
the [START] key (

). Repeat until all pages have

been scanned and then press the

key.

2-SIDED

COPY

SPECIAL FUNCTION

ACC.

DUPLEX SCAN

PQR

2-SIDED

COPY

SPECIAL FUNCTION

SPECIAL FUNCTION
FAX PRINT HOLD
TIMER MODE

SENDING OPTIONS

SENDING OPTIONS
SERIAL POLLING

SUB ADDRESS TX

SUB ADD POLLING

WXYZ

@.-_

READ-END

Pegasus-E_Fax_Ex.book 56

ページ

２００４年１０月１８日　月曜日　午後８時４１分

Содержание AR-FX11





















































































































Результаты поиска

Содержание AR-FX11

Отзывы:

Похожие инструкции для AR-FX11

Бренды по названию

Популярные бренды

Sharp AR-FX11, Руководство по эксплуатации

Результаты поиска

Содержание AR-FX11

Отзывы:

Похожие инструкции для AR-FX11

Бренды по названию

Популярные бренды