Sharp AR-FX11 Скачать руководство пользователя страница 93

Страница: 93 / 116

TROUBLESHOOTING

The transmitted image is
distorted.

Were line conditions poor
due to thunder or another
reason?

Try the transmission
again.

–

Were the resolution and
exposure settings
suitable?

Check the resolution and
exposure settings.

"SELECTING
RESOLUTION AND
EXPOSURE SETTINGS"
on page 15

White or black lines
appear in the transmitted
image.

Is the document glass or
the scanning glass for the
SPF (the long, narrow
glass) dirty?

Clean the document glass
or the scanning glass for
the SPF.

"CLEANING THE
MACHINE" in the
"Operation manual (for
general information and
copier)"

Transmission does not
take place at the specified
time.

Is the machine's clock set
to the correct time?

Set the clock to the correct
time.

"DATE & TIME SET" on
page 99

Printing does not take
place after reception.

Does an error message
appear regarding adding
paper, replenishing toner,
or a misfeed? (This means
that printing is not
possible.)

Restore printing capability
as instructed by the
display message. Printing
will begin.

"WHEN AN ALARM
SOUNDS AND A
WARNING MESSAGE IS
DISPLAYED" on page 88

A received fax prints out
blank.

Was the wrong side of the
original scanned in the
transmitting machine?

Check with the operator of
the transmitting machine.

–

The received image is
faint.

Is the original faint?

Ask the other party to
re-send the fax using a
suitable exposure setting.

–

The received image is
distorted.

Were line conditions poor
due to thunder or another
reason?

Ask the other party to
send the fax again.

–

phon

A dial tone is not heard
through the speaker.

Is the volume set to "low"?

Set the speaker volume to
"middle" or "high".

"SPEAKER VOLUME" on
page 97

The machine does not
ring.

Has the ringer volume
been turned off?

Set the ringer volume to
"low", "middle", or "high".

"SPEAKER VOLUME" on
page 97

Dialling is not possible.

Is the telephone line
properly connected?

Check the connections.

"Line connection" on page
4

If an extension phone is
connected to the machine,
has the "EXTENSION TEL"
program been enabled?

Enable this program.

"EXTENSION TEL" on
page 97

Problem

Check

Solution

Page

Pegasus-E_Fax_Ex.book 91

ページ

２００４年１０月１８日　月曜日　午後８時４１分

Содержание AR-FX11





















































































































Результаты поиска

Содержание AR-FX11

Отзывы:

Похожие инструкции для AR-FX11

Бренды по названию

Популярные бренды

Sharp AR-FX11, Руководство по эксплуатации

Результаты поиска

Содержание AR-FX11

Отзывы:

Похожие инструкции для AR-FX11

Бренды по названию

Популярные бренды