Sharp AR-FX11 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 116

background image

44

ADDING A COVER SHEET/MESSAGE TO
A FAX TRANSMISSION

This function automatically attaches an A4 (8-1/2" x 11") cover sheet to your fax transmissions. The cover sheet
shows the date and time, the destination name, the sender's name and fax number, and the number of pages in the
transmission. A message can also be added to a transmission. One of the following messages can be selected:
"CONFIDENTIAL", "PLEASE DISTRIBUTE", "URGENT", "PLEASE CALL BACK", "IMPORTANT".

Selecting a cover sheet / message

1

In Fax mode, press the [SPECIAL
FUNCTION] key.

When the [SPECIAL
FUNCTION] key is pressed, the
special function menu appears.
(To select fax mode, see step 1
on page 18.)

2

Select "SENDING MENU" with the [

]

or [

] key.

3

Press the [OK] key.

4

To add a cover sheet, select "COVER
SHEET" with the [

] or [

] key. To

add a message, select the desired
message with the [

] or [

] key.

If you do not wish to add a cover sheet, select "NO
CVR. SHEET".
If you do not wish to add a message, select "NO
MESSAGE".

5

Press the [OK] key.

Your machine

The receiving machine

Cover sheet / no message

Cover sheet / message

No cover sheet / message

Select a cover sheet /
message and
transmit the fax.

A cover is automatically
added and the fax is printed.

The selected message is
printed at the top of the cover
sheet.

The selected message is
printed at the top of the
first sheet.

• Select this function before each transmission. The selection is only effective for one transmission. After one

transmission, the function automatically turns off.

• Before adding a cover sheet, make sure that your sender's name and number have been programmed. (See

"OWN PASSCODE SET" on page 96.)

• This function cannot be used when performing a manual transmission, or when using memory polling (page

39), F-code memory polling (page 50), F-code confidential transmission (page 55), or F-code relay request
transmission (page 59).

• You can also enable a setting in the key operator programs to always add a cover sheet to transmissions (see

"AUTO COVER SHEET" on page 103).

DATE

T O

FROM

FAX #

PAGES

: MAY-11-2004 TUE 07:30 PM

: SERVICE CENTRE

: SBC CO.

: 0666211221

: 02PAGES WERE SENT
(INCLUDING THIS PAGE)

AUTOMATIC COVER SHEET

DATE

T O

FROM

FAX #

PAGES

: MAY-11-2004 TUE 07:30 PM

: SERVICE CENTRE

: SBC CO.

: 0666211221

: 02PAGES WERE SENT
(INCLUDING THIS PAGE)

IMPORTANT

AUTOMATIC COVER SHEET

IMPORTANT

Note

2-SIDED

COPY

SPECIAL FUNCTION

ACC.

DUPLEX SCAN

GHI

PQRS

T

2-SIDED

COPY

OK

BACK

SPECIAL FUNCTION
TIMER MODE
SENDING OPTIONS

SENDING MENU

SENDING MENU

NO MESSAGE

CONFIDENTIAL
PLEASE DISTRIBUTE

COVER SHEET

To cancel the cover sheet selection, press the

key instead of the [OK] key in step 3.

Note

Pegasus-E_Fax_Ex.book 44

ページ

２００４年１０月１８日　月曜日　午後８時４１分

«
...
44
45
46
47
48
...
»

Содержание AR-FX11





















































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-FX11

Бренд: Canon Страницы: 2

MARCY PLATINUM MS-91

Бренд: MPEX Страницы: 11

Citymaster 2000

Бренд: HAKO Страницы: 186

Бренд: Singer Страницы: 33

EaglePower SILVER Series

Бренд: IPC Страницы: 8

Бренд: Clarke Страницы: 65

Бренд: Unicorn Страницы: 28

Бренд: Singer Страницы: 109

APW-896N/IP-420

Бренд: JUKI Страницы: 142

AMS-221F3020RSW/AW-3

Бренд: JUKI Страницы: 163

Frozen Gourmet 455

Бренд: Crane Страницы: 57

Бренд: Panasonic Страницы: 112

Бренд: Panasonic Страницы: 144

Бренд: Panasonic Страницы: 172

Бренд: Riccar Страницы: 18

Бренд: Riccar Страницы: 28

Бренд: Riccar Страницы: 45

Бренд: Rhin-O-Tuff Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды