AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 11
Operation/procedure
When the [START] key is pressed, the copy lamp is lighted for 10sec.
Operation/procedure
1.
Select the load to be checked with the 10-key, and press the
[START] key.
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
(20 times)
When the [CUSTOM SETTINGS] is pressed, the operation is interrupted.
The lift-up motor operates only when the tray is opened.
The lift-up motor operates only when the tray is opened.
Operation/procedure
Select the load to be checked with the 10-key, and press the [START] key.
The selected load is operated for 10sec.
Operation/procedure
1.
Select the load to be set with the 10-key.
2.
Press the [START] key.
When selected without setup, the selected value is registered and
highlighted. When selected with previous setup, the previous setup is
canceled and it is displayed normally.
Press [CA] key, and the simulation will be terminated and the machine
goes into the aging standby mode with the set content.
This setting is canceled by power OFF.
*1: When the machine exits from the fusing ignoring state, the roller may
be cooled down. Therefore, reset the machine to warm up again.
When, therefore, the simulation is canceled by pressing the [CA]
key or when the copy mode display is shifted to the initial menu dis-
play in the simulation mode of one page copy, the machine is reset.
5-3
Purpose
Operation test/check
Function
(Purpose)
Used to check the operation of the copy lamp and the
control circuit.
Section
Optical (Image scanning)
Item
Operation
6
6-1
Purpose
Operation test/check
Function
(Purpose)
Used to check the operation of the loads (clutches and
solenoids) in the paper transport system and the
control circuit.
Section
Paper transport (Discharge/Switchback/Transport)
Item
Operation
Item
Content
1
LUM1
1st cassette lift-up motor
2
CPFC1
1st cassette pick-up solenoid
3
CPFS1
1st cassette paper feed clutch
4
MPFS
Manual feed pick-up solenoid
5
RRC
Resist roller clutch
6
PSPS
Separation pawl solenoid
7
OGS
Paper exit gate switching solenoid
8
LUM2
2nd cassette lift-up motor
9
CPFC2
2nd cassette pick-up solenoid
10
CPFS2
2nd cassette paper feed clutch
11
TRC2
2nd cassette transport roller clutch
12
LUM3
3rd cassette lift-up motor
13
CPFC3
3rd cassette pick-up solenoid
14
CPFS3
3rd cassette paper feed clutch
15
TRC3
3rd cassette transport roller clutch
16
LUM4
4th cassette lift-up motor
17
CPFC4
4th cassette pick-up solenoid
18
CPFS4
4th cassette paper feed clutch
6-2
Purpose
Operation test/check
Function
(Purpose)
Used to check the operation of each fan motor and its
control circuit.
Section
Others
Item
Operation
Item
Content
1
VFM
Fusing fan operates
2
DCFM&DCFM2
Power cooling fan, power cooling fan 2
operations
3
VFM2
Fusing exit paper fan operates
3
VFM&DCFM&DCFM2
&VFM2
Fusing fan, power cooling fan, and
power cooling fan 2 are operated at the
same time.
7
7-1
Purpose
Setting/Operation test/check
Function (Purpose)
Used to set the aging operation conditions.
Item
Operation
Item
Content
1
AGING
Aging enable/disable setting
2
MISFEED
Jam detection enable/disable setting
3
FUSING*1
Fusing operation enable/disable setting
The fusing temperature is not controlled.
The heater is not turned ON.
4
INTERVL
Intermittent setting (Valid only when set to AGING.)
5
WARMUP
Warm-up save setting
The machine goes into the ready state only by
shading, disregarding fusing and process control.
After going into the ready state, normal control is
performed.
6
DV CHK.
Developing unit detection enable/disable setting
SIMULATION 6-2
