background image

53

Appendix XI

Limited T wo-Year Scale Warrant y

Setra Systems, Inc. warrants the scales it manufactures to be free from defects in
material and workmanship. Upon return, transportation charges prepaid, to Setra’s
factory within two (2) years of the date of purchase, Setra will repair or replace, at its
option, any scale which it determines to contain defective material or workmanship
and will return said scale to purchaser, transportation prepaid, at any point in the
United States. Setra shall not be obligated, however, to repair or replace scales
which have been repaired by unauthorized parties, abused, improperly installed,
altered, or otherwise misused or damaged, even if by accident, in any way. Setra will
not be responsible for any dismantling, reassembly or reinstallation charges.

Nothing in this warranty shall be construed as a warranty for merchantability or
fitness for any specific use or purpose, and this warranty is in lieu of all other
warranties, express or implied. Setra shall not be held liable under the terms of this
warranty for any special, indirect, incidental or consequential damages claimed in
connection with the scales’ performance or availability.

Setra Systems, Inc.
Weighing Systems Division
159 Swanson Road, Boxborough MA 01719 • (508) 263-1400

Содержание 140CP

























































Отзывы: