Setra Systems 140CP Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 56

Setra Systems 140CP Скачать руководство пользователя страница 7

7

Discharge the battery pack completely each time before recharging to maxi-
mize the life of the battery. A fully charged battery should provide about six
hours of operation.

The battery on/off switch is used only during battery operation to conserve the
charge. Be certain to turn the scale off when not in use during battery operation.
When operating on AC, it is recommended that the scale always be left on. This
reduces warm-up time and keeps a full charge in the battery at all times.

5.

Detaching the controller and weighing platform

Since Setra platform scales have a high weighing capacity, it may be easier to
place the weighing platform on the floor. This will reduce the height to which
heavy weights must be lifted. To allow this type of operation, the CP models
come standard with a detachable controller (keyboard and display). This con-
troller may be placed on a table or wall, while the platform is used on the floor.

To detach the controller, follow the procedure below: (refer to Figure 2)

1.

Remove the pan by grasping it with two hands on the sides and lifting.

2.

Loosen the controller attaching screws. The controller will drop down
until it rests on its own feet.

3.

Lift up the front of the weighing platform and slide the controller out
from underneath.

Replace the pan by visually centering it on the scale and pressing it in place
until well seated. The pan will be seated correctly if it is level on all sides.

To replace the controller, follow this procedure:

1.

Remove the pan by grasping it with two hands on the sides and lifting.

2.

Pull the cable out of the weighing platform in order to obtain some
tension.

3.

Pack as much cable as possible into the retainer on the rear of the
controller. The cable must be double folded in order to store it
completely.

4.

Lift up on the front of the weighing platform and slide the controller
under the front lip.

5.

Align the controller with the attaching screws and engage them by
hand for several turns.

CAUTION: TO PREVENT CROSS-THREADING, DO NOT USE A SCREWDRIVER TO

ENGAGE THE ATTACHING SCREWS.

«
...
5
6
7
8
9
...
»

Содержание 140CP

























































Отзывы:

Нет отзывов