Seneca S6001-RTU Скачать руководство пользователя

Страница: 146 / 210

USER MANUAL – Z-TWS4/Z-PASS2-S/S6001-RTU

146

In this page, for each of the two available Ethernet interfaces (LAN and WAN), the following information is
shown:



the Ethernet link status (i.e. “Down” or “Up”)



the number of packets/bytes received from the Ethernet interface, when the link is up; “0/0” when
the link is down



the number of packets/bytes sent to the Ethernet interface, when the link is up; “0/0” when the
link is down

For Z-TWS4, Z-PASS2-S, S6001-RTU and for Z-PASS2-S-R01/Z-PASS2-S-IO/Z-TWS4-IO when the “Ethernet
Mode” is “Switch”, the “Ethernet Interfaces” page is similar to the one shown in the following figure.

Содержание S6001-RTU



















































































































































































































Результаты поиска

Содержание S6001-RTU

Отзывы:

Похожие инструкции для S6001-RTU

Бренды по названию

Популярные бренды

Seneca S6001-RTU, Руководство пользователя

Результаты поиска

Содержание S6001-RTU

Отзывы:

Похожие инструкции для S6001-RTU

Бренды по названию

Популярные бренды