SENEC HOME LI, Перевод инструкций по установке

Страница: 32 / 74

32
7.2.3 Connection where the metering point cannot be assigned
You must use this connection variant if a non-certified inverter is used and the domestic consumption cannot
be unambiguously assigned at the metering point (e.g. if the consumption is distributed over a number of
properties). In this case, you clamp power flow direction sensor 3 (blue/lilac network cable) directly behind
the PV inverter. Input and output are swapped here.
Grid Generator Consumer
OK ESC
Passiv
Laden
Entladen
Störung
37 36 35
ABB
M14
Drehstromz ä hler
1376
T1 T2 T4 T3 KD PD T4 D Ü FF SET
2014 Made in EU
Type MT174-D1A52-V22-M3K03Z
3x230/400 V 0,25-5(85) A
Schltg.: IS16050
0.9.1
0.9.2
x.7.0 1.8.0
1.8.x
2.8.0 2.8.x
F.F.0
Uhrzeit
Datum
Aktuelle Wirkleistung (kW) Gesamt-Wirkenergie A+ (kWh)
Wirkenergie A+ Tarif x (kWh)
Gesamt-Wirkener A- (kWh) Wirkenergie A- Tarif x (kWh)
Fataler Fehler
SI 12-11-007 MID
-40 °C bis +70 °C
20.15
14.03
50 Hz
RLw=1000 Imp./kWh
Eigentum des Messstellenbetreibers
1 ISK00 6393 8492
27.743.806
Nr. 63 938 492
51 7351
14
40
ER
L1 L2 L3
kW
M14
Drehstromz ä hler
1376
T1 T2 T4 T3 KD PD T4 D Ü FF SET
2014 Made in EU
Type MT174-D1A52-V22-M3K03Z
3x230/400 V 0,25-5(85) A
Schltg.: IS16050
0.9.1
0.9.2
x.7.0
1.8.0
1.8.x
2.8.0
2.8.x
F.F.0
Uhrzeit
Datum
Aktuelle Wirkleistung (kW)
Gesamt-Wirkenergie A+ (kWh)
Wirkenergie A+ Tarif x (kWh)
Gesamt-Wirkener A- (kWh)
Wirkenergie A- Tarif x (kWh)
Fataler Fehler
SI 12-11-007 MID
-40 °C bis +70 °C
20.15
14.03
50 Hz
R Lw =1000 Imp./kWh
Eigentum des Messstellenbetreibers
1 ISK00 6393 8492
27.7
43.806
Nr. 63 938 492
51 7351
14
40
ER
L1 L2 L3
kW
3736 35
ABB
1 2
3
4
5
7
6
8
Figure 10 Connection variant 3 where the metering point cannot be assigned
1
Meter operator's up-and-down meter
7
All the consumers in the house
2 Power flow direction sensor 1 8 SENEC.Home Li storage unit
3 Power flow direction sensor 3 Main lines
4 PV installation generation meter (if needed) Communication
5
PV inverter (if needed)
6
House wiring
Note!
Power flow direction sensor 3 is not supplied and must be ordered
separately specifying the transformer ratio required.
Note!
Fit power flow direction sensor 3 inverted (input at bottom, output at top),
so that it meters generation and not consumption (negative values).
The display on the power flow direction sensor thus does not indicate
any current values.