Seepex BN 100-6LS Скачать руководство пользователя страница 31

Страница: 31 / 70

Ausgabe
issue

D / 04.02.2013

Dokument
document

OM.SCT.02e

Blatt
sheet

3 (18)

Dismantling/reassembly

9.1.2 Rotor (600), stator (601) - reassembly - SCT

9.1.2.1 Rotor (600) - reassembly

Tool (WZ/circlip tongs 45°)



Spread the circlip (643) wide enough so
that it can be released.

–

Use tool (WZ).



Slide circlip (643) towards rotor (600).



Slide support ring (682) towards rotor
(600).



Remove the lock washer (683).

–

Use a suitable tool (WS).



Remove rotor (600) from rotor head (640).



Remove support ring (682), circlip (643)
and O-ring (642) from rotor (600).



Insert O-ring (642) in rotor (600) groove.



Slide circlip (643) and support ring (682)
onto rotor (600).

–

Note the fitting position of support ring
(682).



Coat the inner surfaces of the rotor head
(640) with graphite petroleum.



Slide rotor (600) into rotor head (640).

Содержание BN 100-6LS







































































Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды

Seepex BN 100-6LS, Руководство по эксплуатации и сборке

Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды