Seepex BN 100-6LS Скачать руководство пользователя страница 43

Страница: 43 / 70

Ausgabe
issue

D / 04.02.2013

Dokument
document

OM.SCT.02e

Blatt
sheet

15 (18)

Dismantling/reassembly

Tool (W29/lifting equipment incl. lashing strap)



Secure rotor (600).

–

Use tool (W29).



Attach the lower half of the stator (601.u).



Press the stator half (601.u) onto the ta-
pered surfaces of the segment receiver
(671) and align it.



Avoid damage to the stator surfaces.



The tapered stator surface (601.u) is in
contact with the segment retainer (671) ta-
pered surface.



Observe the segment order.

–

* = A-A, B-B, C-C, D-D



Secure the lower half of the stator (601.u).

–

Fix the lower adjusting segments
(635) to the segment retainer (671).



Tighten the screws until the adjusting seg-
ments (635) interlock with the guide of the
segment retainer (671) (detail x).

Tool (W29/lifting equipment incl. lashing strap)



Remove the tool (W29).

Содержание BN 100-6LS







































































Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды

Seepex BN 100-6LS, Руководство по эксплуатации и сборке

Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды