Seepex BN 100-6LS Скачать руководство пользователя страница 17

Страница: 17 / 70

Ausgabe
issue

A / 15.05.2013

Dokument
document

OM.INS.09e

Blatt
sheet

1 (2)

Assembly / Installation

5.1

Mounting tools / lifting gear

5.2

Space requirement

The required space should be determined by considering the following factors:

•

Dimensions and weight.

•

Requisite transport and lifting equipment.

•

Pipe routing – dismantling (dimension for stator replacement).

5.2.1 Dimension for stator replacement (P)

5.3

Assembly of the complete mounted pump



Assemble according to technical data (



chapter 3.).



Note dimensional drawing.

Tension-free mounting of the pump



Balance unevenness with suitable supports.

•

Applies to mounting on foundations/load-bearing elements.

•

Total areas of all pump bearing areas are resting on the surface.

Correct position of the drives

•

All drives are set up ready for operation and mounted.

•

Correct displacements of the drive during transport/installation of the pump by adjusting/fix-
ing the drive.

CAUTION

Pump falling over.

Slight injury or damage to property can occur.



Adhere to the lifting tool’s starting point.



Pay attention to the dimensions, weight and centre of gravity of the pump.



Use suitable mounting tools/lifting gear.

Range

Dimension (P)

5-6LS

320 mm

10-6LS

350 mm

17-6LS

405 mm

35-6LS

510 mm

52-6LS

570 mm

70-6LS

605 mm

100-6LS

605 mm

130-6LS

720 mm

CAUTION

Safety protection equipment.

Slight injury or damage to property may result.



Connect safety protection equipment and activate.

Содержание BN 100-6LS







































































Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды

Seepex BN 100-6LS, Руководство по эксплуатации и сборке

Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды