Seepex BN 100-6LS Скачать руководство пользователя страница 48

Страница: 48 / 70

Dismantling/reassembly

Ausgabe
issue

A / 05.12.2012

Dokument
document

OM.PJT.21e

Blatt
sheet

2 (5)

9.2.2 Rotating unit (RTE) – preparing component parts for assembly

9.2.2.1 Prepare rotor head (640) for assembly

9.2.2.2 Prepare coupling rod (400) for assembly

9.2.2.3 Prepare plug-in shaft (307) for assembly



Remove existing damage.



Clean the plug-in shaft (307).



Bend (A) the coupling rod (400).



Knock guide bushing (403) out.

–

Use tool (W5).



Remove coupling rod (400).



Remove any damage.



Clean rotor (600).

Tool (W4/assembly mandrel)



Press in guide bushings (403)

(depth = 2/3).

–

Use tool (W4).



Clean the coupling rod (400).



Examine bore head for wear.

–

If wearing is detected on the bore
head, replace the coupling rod (400).

Tool (W4/assembly mandrel)



Press in guide bushings (403)

(depth = 2/3).

–

Use tool (W4).

Содержание BN 100-6LS







































































Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды

Seepex BN 100-6LS, Руководство по эксплуатации и сборке

Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды